Sika Emseal offers a multitude of watertight expansion joint systems to ensure a static tie-in to the waterproofing membrane in split-slabs and plaza deck joints. Thoughtfully designed transitions ensure continuity of the building enclosure - https://www.emseal.com/product/watertight-expansion-joint-transitions/ RoofJoint (https://www.emseal.com/product/roofjoint-roof-expansion-joint/) can be used in split-slab and hardscaped decks when drainage or other construction may be impeded by the expansion joint protruding above the structural deck elevation. In these cases an additional expansion joint seal would be needed at the wearing course. (See SJS, DSM and DSM-DS.) As with roof applications where a fire-rated seal is also required, Emshield DFR can be installed directly below the RoofJoint. When transitioning to a vertical wall expansion joint, Seismic Colorseal can be used. SJS: https://www.emseal.com/product/sjs-seismic-joint-system-seismic-expansion-joint/ DSM: https://www.emseal.com/product/dsm-system-watertight-expansion-joint/ Emshield DFR: https://www.emseal.com/product/dfr2-fire-rated-expansion-joint-floors/ Seismic Colorseal: https://www.emseal.com/product/seismic-colorseal-wall-expansion-joint-3/ A seismic plaza deck expansion joint system the SJS-FP System (https://www.emseal.com/product/sjs-fp-seismic-plaza-deck-expansion-joint/) is designed to provide a watertight, trafficable joint system in wide expansion joints in hardscaped decks of split-slab design. SJS-FP expands the use of the SJS System to waterproofed hardscaped split-slab deck designs through the use of structural-slab mounted retainer legs with integral waterproofing side sheets that integrate with the deck waterproofing membrane. The retainer legs are available in leg heights that can be matched to the topping slab or wear course thickness. The waterproofing side sheets lock into the top of the retainer legs and are embedded in and encapsulated by the deck waterproofing membrane. The SJS System foam/spline assembly installs between the faces of the retainer legs. The foam/spline assembly is constructed from two precompressed foam sealants pre-assembled in parallel adjacent to a heavy-duty extruded aluminum spline. The spline acts as a receptor for attaching the surface-mounted traffic plates that bear vehicle and other loads. The result is a system that is watertight and covered with a cover plate that is securely anchored into the wear course. A plaza-deck to solid-slab or wall expansion joint, DSM-FP is watertight and purpose designed for use in plaza decks particularly where a split-slab meets a solid slab or wall - https://www.emseal.com/product/dsm-fp-watertight-plaza-deck-expansion-joint/ DSM-FP extends the use of the DSM System to waterproofed split-slab deck designs through combination with our FP (for plaza) mounting rails and side flashing sheets that integrate with the deck waterproofing membrane and contain the wearing course. The material that bridges and seals between the FP mounting rails is Emseal’s DSM System which is a silicone-and-impregnated-foam hybrid sealant that ensures watertightness, absorbs sound, dampens vibration and offers uncomplicated installation. In contrast to buried joint systems, Emseal’s FP Systems prevent the buckling of pavers or other hardscaped wear course materials and will not suffer flex-fatigue failure at the waterproofing membrane tie-in. A plaza deck expansion joint, Migutan FP110 and FP155 (https://www.emseal.com/product/migutan-plaza-deck-expansion-joint/) are unique designs incorporating side membrane sheets which integrate with the deck waterproofing system to form a continuous, completely watertight system. For applications, particularly over occupied space, where totally watertight integration of expansion joint and deck membrane is a fundamental requirement. Application examples include hardscaped split-slab construction on plaza (podium) decks, split-slab parking decks, stadium concourses, and anywhere waterproofed split slab construction is specified. For applications with softscaped toppings (green roofs, garden roofs, under landscaping) see RoofJoint - https://www.emseal.com/product/roofjoint-roof-expansion-joint/ Highly configurable, using factory-fabricated transitions, to a multitude of field conditions, Migutan is the only system of its kind with a 20-year track record and tens of thousands of feet installed and functioning. Links: Contact Sika Emseal: https://www.emseal.com/expansion-joint-resources/where-to-buy-emseal-contact-us/ Split-Slab: https://www.emseal.com/glossary-term/split-slab/ Continuity of Seal: https://www.emseal.com/glossary-term/continuity-of-seal/ Plaza Deck Selection Guide: https://www.emseal.com/product-type/split-slab-plaza-deck-expansion-joint-selection-guide/

Watertight Wall Expansion Joints by Sika Emseal are easy to install high-movement capable systems. Watertight, thermal insulating and sound attenuating. For interior or exterior use, they are available in many industry standard silicone colors. This quick overview shows the product and how easy it is to install. Your best choice for new or retrofit construction. The best wall expansion joint product, is a silicone-coated, precompressed primary seal for high-movement wall joints. These products are designed for watertightness in vertical-plane structural, seismic, and abutment joints in virtually any substrate. Continuity of seal and continuity of thermal insulation throughout changes in plane and direction are hallmarks of our precompressed vertical expansion joint systems. The product’s ability to maintain watertightness when installed at inside corners, and while handling curves and direction changes further sets it apart from rubber-and-rail strip seals. The backpressure from the 100% acrylic impregnated polyurethane foam is positively secured without invasive anchors while color-switching makes the product aesthetically versatile. These expansion joint systems were developed to restore the function of the building envelope where it is breached by the location of a movement joint. As a result, the performance tests required to certify curtainwall and other building envelope systems are the basis of performance. Sika Emseal wall expansion joint systems have been tested to, and exceeds, the requirements of performance tests including: for Water Penetration: ASTM E-331; Wind Loading: ASTM E330; Air permeability: ASTM E283-04; Sound blocking: ASTM E90-09; R-Value: ASTM C518-04; Low-Emitting Material : CDPH/EHLB/Standard Method Version 1.2, 2017; as well as in-house Temperature Stability, Bleeding, Staining & Recovery testing to ensure performance under conditions modeling real life. More on our expansion joint systems at www.emseal.com FEATURES: -Primary seal -Watertight -Airtight -Insulates -Non-invasive anchoring -Low-Emitting Material per CDPH/EHLB V1.2, 2017 -Sound attenuating STC 52; OITC 38 -ABAA Compliant -Resists hurricane force wind & water -Low-Tension silicone and foam hybrid sealant -Rapid installation–new or retrofit -Aesthetically and practically versatile -Easily handles changes in plane and direction -Easily handles curved expansion joints USES: -Curtainwall: https://www.emseal.com/project/wall-expansion-joints-northwestern-kellogg-school/ -Masonry -Precast -Metal Panel -Natural Stone -EIFS, etc. -Rough Substrates: https://www.emseal.com/rough-expansion-joint-substrates/ -Curved Expansion Joints: https://www.emseal.com/article/curved-expansion-joints/ SIZES: 1/2″ to 10″ | 12mm – 250mm Note: Sizes under 1 1/2″ (40mm) are manufactured with a single bellows (See Colorseal-On-A-Reel) and are supplied as 10′ lengths on reels. Larger sizes incorporate multiple bellows and are supplied as 6.56′ (2M) long ‘sticks’. MOVEMENT: Total 100% (+50% and -50%) of nominal supplied size. COLOR: Full range of industry standard colors: https://www.emseal.com/color-selection/ FEATURES: Watertight—the low tension silicone bellows is installed just back from the wall surface. This ensures watertightness is achieved at the face of the wall preventing water getting trapped against the substrates or within the joint cavity. Non-Invasive Anchoring—there are no hard metal-to-substrate connections in the system. This includes embedded pins, anchors, screws, bolts or tracks, trays or rails that often damage sensitive substrates and act as a thermal bridge. Non-invasive anchoring means the system is locked to the joint faces by means of the 1) backpressure of the foam, 2) the injected silicone corner bead at the joint face to foam and silicone bellows interface. Continuity of Seal—as in all EMSEAL expansion joint systems, continuity of seal through changes in plane and direction is an essential performance differentiator. Details for watertight, transitions using factory-fabricated Universal and Custom transitions pieces are available from EMSEAL. Roof Closures are also available to ensure continuity of seal from wall joints to our RoofJoint roof expansion joint system: https://www.emseal.com/whats-best-roof-expansion-joint-design/ Aesthetics & Versatility— Various industry standard colors, uniform bellows appearance, ability to handle variations in joint size are among other system features.

RoofJoint(https://www.emseal.com/product/roofjoint-roof-expansion-joint/) is a watertight roof expansion joint from Sika Emseal. It provides a watertight seal for expansion gaps on the roof and also transitioning to walls. It's a patented dual-seal, double-flanged, extruded thermoplastic rubber system for sealing expansion joints in roofs, plaza assemblies, green and vegetative roofs. Watertightness is achieved through positive integration with the roofing membrane and a purpose-designed system for transitioning between the joint in the roof and joints in walls. Movement at the joint is accommodated by the folding design of the gland. The double-cell configuration provides two levels of sealing. The geometric shape is purpose-designed for the lowest strain during movement to ensure longevity. In addition to roof applications, RoofJoint can be effectively used for softscape plazas as well as split slab and hardscaped decks when drainage or other construction may be impeded by the expansion joint protruding above the structural deck elevation. In these cases an additional expansion joint seal would be needed at the wearing course. (See Emseal’s SJS, DSM and DSM-DS.) As with roof applications where a fire-rated seal is also required, Emshield DFR can be installed directly below the RoofJoint. Product information at: https://www.emseal.com/product/roofjoint-roof-expansion-joint/ SJS: https://www.emseal.com/product/sjs-seismic-joint-system-seismic-expansion-joint/ DSM: https://www.emseal.com/product/dsm-system-watertight-expansion-joint/ Emshield DFR: https://www.emseal.com/product/dfr2-fire-rated-expansion-joint-floors/ Seismic Colorseal: https://www.emseal.com/product/seismic-colorseal-wall-expansion-joint-3/ Transitions: https://www.emseal.com/product/watertight-expansion-joint-transitions/ Features High movement Redundant sealing Double-level roof-membrane integration flanges Redundant fastening—adhesion or welding & termination bar Factory heat welded transitions at tees, crosses, roof-to-wall, etc. Watertight transition to Seismic Colorseal wall joints using RoofJoint Closures Uniquely addresses wall joint to roof joint interface UV-stable NPVC version available for welding compatibility with PVC membranes, as well as for adhering into asphaltic, SBS, mod-bit, or thermoset rubber roof membranes White TPV version available for direct welding into TPO reflective roof membranes Can be fire-rated with installation of Emshield DFR System includes necessary termination bar and fasteners required for installation. Sizes RJ-0200: 2-3 inches | 50-75mm RJ-0400: 3-5 inches | 75-125mm RJ-0600: 5-7 inches | 125-175mm RJ-0800: 7-9 inches | 175-225mm Movement RJ-0200: 2 1/2 inches | 60mm RJ-0400: 5 inches | 125mm RJ-0600: 7 inches | 175mm RJ-0800: 9 inches | 225mm Uses Flat roofs Sloped roofs Green, garden, vegetative roofs Plaza deck and split-slab assemblies Roof to wall joint transitions https://www.emseal.com/product/watertight-expansion-joint-transitions/ Tie in to hot rubber roofs Weld to PVC roofs Adhere to mod-bit roofs Adhere to torch-applied roofs Weld to TPO roofs Non-roof applications in split slab and hardscaped decks U.S. Patents US Patent: 10,851,542 US Patent: 9,850,662 US Patent: 9,739,050 US Patent: 9,322,163

Fire rated wall expansion joint, Emshield WFR (Wall, Fire-Rated) is a watertight, 1, 2, or 3-hour fire-rated, dual-sided primary seal for repair, retrofit, and new installation in structural expansion joints and construction joints in vertical plane wall and head-of-wall applications. Emshield WFR is a UL / ULC-certified fire barrier and preformed alternate to fire caulk and fire stop materials. It features dual-sided silicone sealing surfaces adhered to a fire-retardant impregnated foam backing. Both sides of the expansion joint are waterproof and fire-rated. Emshield WFR eliminates the need for fire blankets, mineral wools, liquid sealants, fire caulk, cover plates, or other fire stop materials. It can be used alone or under any other expansion joint cover, plate or filler where depth of substrate allows–with Emshield WFR one install does it all. Non-invasive anchoring vastly simplifies installation and project sequencing. Emshield WFR fire rated wall expansion joint is tested and certified by Underwriters Laboratories (UL), to the rigors of UL 2079 for wall and head-of-wall expansion joints as well as to California Department of Public Health CDPH/EHLB/Standard Method Version 1.2, 2017 for low-emitting materials.

A Single-Unit, 2 or 3-Hour, UL2079, UL/ULC-certified fire and water resistant expansion joint system for floors and decks. More here: https://www.emseal.com/product/dfr2-fire-rated-expansion-joint-floors/ A fire rated expansion joint, Emshield DFR is a watertight, traffic durable primary seal for repair, retrofit, and new installation in structural expansion joints and construction joints in horizontal-plane applications. Emshield DFR eliminates the need for fire blankets, mineral wools, liquid sealants or other fire stop materials. It can be used alone or under any other expansion joint cover, plate or filler where depth of substrate allows. Installed entirely from the deck surface, Emshield DFR vastly simplifies installation, project sequencing and coordination of trades by eliminating the need for access staging or obstruction by installation and presence of under-slab mechanical systems. Emshield DFR is tested and certified by Underwriters Laboratories (UL), to the rigors of UL 2079 for deck and floor expansion joints: https://www.emseal.com/article/ul-2079-decks-floors/ Certified to California Department of Public Health CDPH/EHLB/Standard Method Version 1.2, 2017 for low-emitting materials: https://cdn.emseal.com/wp-content/uploads/2017/11/CA-Specification-01350-Low-Emitting-Material-Certification-Emshield-DWFR-Fire-Rated-Expansion-Joint-EMSEAL.pdf Features - Traffic durable - Watertight - ADA Compliant - 2 & 3-Hour Fire Rated to UL 2079 - Applications beyond UL Listing by engineered judgment - Non-invasive anchoring - Low-Emitting Material per CDPH/EHLB V1.2, 2017 - Installed entirely from the deck or floor above–no utility lifts or holding labor required - No obstructions columns or underslab obstructions from HVAC, electrical, plumbing or mechanical materials - Eliminates the need for fire blankets and gutters - Meets the requirements of ASTM E1966, ASTM E119 and ASTM E1399 - One Install Does It All–fire-rated, watertight, traffic bearing, 100% movement, quiet, non-invasive anchoring, UL 2079 Certified for decks and floors Uses For floors and decks Interior and open air Stadiums Parking decks Stair tower perimeters Deck-to-deck Deck-to-wall Ceilings Arenas Floors Stair/elevator tower perimeters Interior floors under joint covers

Expansion Joint EMSEAL’s Seismic Colorseal is an easy to install high-movement wall and vertical expansion joint. Watertight, thermal insulating and sound attenuating. For interior or exterior use it is available in many industry standard silicone colors.This quick overview shows the product and how easy it is to install. Your best choice for new or retrofit construction. A wall expansion joint, Seismic Colorseal (Colorseal) is a silicone-coated, precompressed primary seal for high-movement wall joints. Seismic Colorseal ensures watertightness in vertical-plane structural, seismic, and abutment joints in virtually any substrate. Continuity of seal and continuity of thermal insulation throughout changes in plane and direction are hallmarks of Seismic Colorseal. The product’s ability to maintain watertightness when installed at inside corners, and while handling curves and direction changes further sets it apart from rubber-and-rail strip seals. Seismic Colorseal is positively secured without invasive anchors while color-switching makes the product aesthetically versatile. Seismic Colorseal was developed to restore the function of the building envelope where it is breached by the location of a movement joint. As a result, the performance tests required to certify curtainwall and other building envelope systems are the basis of performance of Seismic Colorseal as well. Seismic Colorseal has been tested to, and exceeds, the requirements of performance tests including: for Water Penetration: ASTM E-331; Wind Loading: ASTM E330; Air permeability: ASTM E283-04; Sound blocking: ASTM E90-09; R-Value: ASTM C518-04; Low-Emitting Material : CDPH/EHLB/Standard Method Version 1.2, 2017; as well as in-house Temperature Stability, Bleeding, Staining & Recovery testing to ensure performance under conditions modeling real life. More on Seismic Colorseal at emseal.com: https://www.emseal.com/product/seismic-colorseal-wall-expansion-joint-2/ FEATURES: -Primary seal -Watertight -Airtight -Insulates -Non-invasive anchoring -Low-Emitting Material per CDPH/EHLB V1.2, 2017 -Sound attenuating STC 52; OITC 38 -ABAA Compliant -Resists hurricane force wind & water -Low-Tension silicone and foam hybrid sealant -Rapid installation–new or retrofit -Aesthetically and practically versatile -Easily handles changes in plane and direction -Easily handles curved expansion joints USES: -Curtainwall: https://www.emseal.com/project/wall-expansion-joints-northwestern-kellogg-school/ -Masonry -Precast -Metal Panel -Natural Stone -EIFS, etc. -Rough Substrates: https://www.emseal.com/rough-expansion-joint-substrates/ -Curved Expansion Joints: https://www.emseal.com/article/curved-expansion-joints/ SIZES: 1/2″ to 10″ | 12mm – 250mm Note: Sizes under 1 1/2″ (40mm) are manufactured with a single bellows (See Colorseal-On-A-Reel) and are supplied as 10′ lengths on reels. Larger sizes incorporate multiple bellows and are supplied as 6.56′ (2M) long ‘sticks’. MOVEMENT: Total 100% (+50% and -50%) of nominal supplied size. COLOR: Full range of industry standard colors: https://www.emseal.com/color-selection/ FEATURES: Watertight—the low tension silicone bellows is installed just back from the wall surface. This ensures watertightness is achieved at the face of the wall preventing water getting trapped against the substrates or within the joint cavity. Non-Invasive Anchoring—there are no hard metal-to-substrate connections in the system. This includes embedded pins, anchors, screws, bolts or tracks, trays or rails that often damage sensitive substrates and act as a thermal bridge. Non-invasive anchoring means the system is locked to the joint faces by means of the 1) backpressure of the foam, 2) the injected silicone corner bead at the joint face to foam and silicone bellows interface. Continuity of Seal—as in all EMSEAL expansion joint systems, continuity of seal through changes in plane and direction is an essential performance differentiator. Details for watertight, transitions using factory-fabricated Universal and Custom transitions pieces are available from EMSEAL. Seismic Colorseal Roof Closures are also available to ensure continuity of seal from wall joints to our RoofJoint roof expansion joint system. Aesthetics & Versatility—26 standard colors, uniform bellows appearance, ability to handle variations in joint size are among other system features.

EMSEAL's SJS seismic expansion joint system is the industry standard for larger, watertight expansion joints used in parking garages, decks, walkways and other horizontal areas with vehicular or pedestrian traffic requiring a coverplate. This quick overview shows the product and how easy it is to install. The EMSEAL SJS System is the best solution to your new construction or retrofit repair larger horizontal expansion joint needs. More on SJS here: https://www.emseal.com/product/sjs-seismic-joint-system-seismic-expansion-joint/ A seismic expansion joint, the SJS System is watertight and features a trafficable cover plate that is not attached to the concrete deck. It is comprised of silicone-and-impregnated-foam hybrid components that ensure watertightness, absorb sound, dampen vibration and offer uncomplicated installation. Specify SJS-FR for all the benefits of SJS with the added life safety assurance of a built-in UL 2079 fire rating. SJS is constructed from two precompressed hybrid foam sealants pre-assembled in parallel adjacent to a heavy-duty extruded aluminum spline. The spline acts as a receptor for attaching the surface-mounted traffic plates that bear vehicle and other loads. The result is a system that offers features and benefits not found in alternative products intended for large, horizontal structural joint gaps. Unlike side-mounted coverplates, the SJS plate is not anchored into the concrete and will not loosen during load transfer and vertical deflection movement. Watertight at the deck surface, the SJS System does not rely on gutters that hang under the joint. Water is thus not trapped where it must be managed away. FIRE RATED & Watertight: SJS is available also with a built-in UL-Listed fire rating. More on SJS-FR here: https://www.emseal.com/product/sjs-fr-fire-rated-seismic-expansion-joint/ FOR PLAZA DECKS: SJS is available with FP (For Plaza) leg assemblies and integral side flashing sheets that tie into plaza deck or split-slab buried waterproofing membranes on the structural slab. More on SJS-FP here: https://www.emseal.com/product/sjs-fp-seismic-plaza-deck-expansion-joint/ FIRE RATED FOR PLAZA DECKS: A UL-Listed, UL-2079 tested system for plaza decks SJS-FP-FR achieves waterproofing and fire rating in plaza decks in a single assembly installed from above the deck with no need to access the underside of the structural slab. More on SJS-FP-FR here: https://www.emseal.com/product/sjs-fp-fr-fire-rated-plaza-deck-expansion-joint/ Watertight – The tensionless silicone bellows are installed flush to the mounting height of the system and just below the cover plate ensuring watertightness at the traffic surface. This eliminates the need for ineffective moisture barriers and secondary gutter systems. SJS System is also available specifically for watertight integration with split-slab buried waterproofing systems–see SJS-FP. Sound Dampened – The flanking impregnated foam and silicone hybrid dampens sound and shock effectively. When installed over EMSEAL-supplied elastomeric nosing material Emcrete, the result is arguably the quietest watertight cover plate system available. (Video: See and hear the SJS difference.) Installs Rapidly – Using non-invasive anchoring the SJS System eliminates drilling associated with hard metal-to-concrete connections as well as intrusive pins, anchors, screws, bolts or tracks, trays or rails. The system is locked to the joint faces by the backpressure of the foam and an epoxy adhesive, and by the injection of a silicone sealant band at the bellows to substrate interface. (Video of installation in a parking deck or a stadium at the New York Mets and the San Francisco 49ers). Self-Locating Cover Plate Screws – The center spline is a continuous receptor for the cover plate screws that are self-tapped into the anchor channel. This dramatically reduces the installation-related problems of locating self-centering, sliding ball devices and pantographs. The probability of screws being left out is eliminated ensuring proper anchoring. Self-Locking, Vibration-Dampened Screws – Vibration in systems that rely on metal-to-metal connections and contact points is the main cause of screw loosening. SJS minimizes vibration through the dampening action of the massive and continuous springs of impregnated foam along the entire length of the joint. In addition, 30 pounds of force is required to loosen the screws offering excellent screw tightness without the need for thread-lock compounds. Continuity of Seal – All EMSEAL expansion joint systems feature continuity of seal through changes in plane and direction –– an essential performance differentiator. Interlocking or continuous fabricated transitions for curbs, sidewalks, treads and risers, and parapets for example, are available with the SJS System.

EMSEAL's DSM System is the industry standard for watertight expansion joints used in parking garages, decks, walkways, stadiums and other horizontal areas with vehicular or pedestrian traffic. This quick overview shows the product and how easy it is to install. EMSEAL DSM System is the best solution to your new construction or retrofit repair horizontal expansion joint needs. https://www.emseal.com/product/dsm-system-watertight-expansion-joint/ A watertight expansion joint, the DSM System is for horizontal-plane deck applications. Traffic durable, joint-face adhered and precompressed, DSM System is a primary seal for deck expansion joints. DSM’s toughness and resilience come from its microsphere-modified-acrylic impregnation and tensionless highway-grade silicone bellows coating. The system is comprised of 1) pre-compressed, silicone-and-impregnated-foam hybrid; 2) field-applied epoxy adhesive on the joint faces; 3) a silicone sealant band that seals substrate voids and irregularities. An unmatched performance record has established DSM System as a standard for parking deck and stadium expansion joint sealing. Unlike extruded rubber seals, ‘caulk-and-backer rod’ and other predecessor technologies, DSM does not suffer from compression-set nor does it rely on adhesion in tension for its performance. Highly configurable, the DSM System uniquely handles changes in plane and direction essential to ensuring continuity of seal. Watertight—the system is installed just below the deck surface. This ensures watertightness is achieved at the deck surface not in gutters from which water must be managed. Non-Invasive Anchoring—there are no hard metal-to-concrete connections in the system. This includes embedded pins, anchors, screws, bolts or tracks, trays or rails. The system is locked to the joint faces by means of the 1) backpressure of the foam, 2) the epoxy adhesive, and 3) the injected silicone sealant band at the joint face to foam and silicone bellows interface. Continuity of Seal—as in all EMSEAL expansion joint systems, continuity of seal through changes in plane and direction is an essential performance differentiator. Details for watertight, field-fabricated transitions from deck to wall, at curbs, sidewalks, parapets, tees, and crosses are available with the DSM SYSTEM. Aesthetics & Versatility—Standard color is gray (other colors available), uniform bellows appearance, double sealing, fuel resistance, and an enhanced ability to handle variations in joint size are among other system features. Transitions and Terminations https://www.emseal.com/product/universal-custom-90s/ Universal-90’s: Universal-90’s (or U-90’s) are factory-made 90-degree transition pieces that ensure continuity-of-seal where expansion joints change plane. Use of U-90’s eliminates the field work needed to make plane changes making overall installation fast and efficient. Watertightness through the plane change is guaranteed–leaving nothing to chance in field-fabricating inside and outside transitions. U-90 transitions are symmetrically coated on both faces allowing them to be installed as an inside corner or as an outside corner. Straight-run sticks are joined in the field to the U-90’s. U-90’s have a 12-inch (305mm) long leg and a 6-inch (152mm) vertical piece on each side of the elbow. Custom-90’s: Custom-90’s, are factory-fabricated inside and outside 90-degree transition pieces coated on just the weather-facing faces. Custom-90’s are available when field conditions and measurements are known up front. Custom-90’s are widely used in stadium tread and riser applications or other applications where numerous inside and outside 90-degree transitions are required. Consult EMSEAL.